Wednesday, 18 May 2011

Quadcopters Uk Have Stock Of X650C

Quadcopters.co.uk Have stock of the X650 Carbon version at the moment.
We are European and Uk Distributors of the Xaircraft range of Quadcopters and carry a full range of spares and accessories including fpv equipment and 5.8ghz Video transmitters and receivers.
We ship worldwide and to Europe including , Germany , France , Italy and even customers as far as Australia.

Monday, 2 May 2011

Xaircraft Latest Firmware Updates

Http://www.quadcopters.co.uk





                             
Here are links to the latest Xaircraft Firmware releases . 
All the Xaircraft range of Quads and accessories can be found at our main site Quadcopters
We will keep this page updated with latest firmware updates as we get them,

XAircraft Latest Configuration Software V1.1.5.414 supports gps and compass Released on the 14/04/2011
Download here

XAircraft Flight Controller Firmware v1.31 can be downloaded from http://www.xaircraft.com/wiki/images/e/ed/Flight_Controller_1.31_en.xfw

AHRS-S Attitude & Heading Reference System Firmware Download
Latest Version v1.20 can be downloaded from 

Please note v1.31 is not compatible with the old settings pack so you will need to download and 
install the latest settings pack , Download from 
http://www.xaircraft.com/wiki/images/d/d3/FC1212-S_1.31_Settings_Pack_en.zip

Sunday, 1 May 2011

XAircraft X450 build log by Quadcopters Uk

 

XAircraft X450 Build Thread by Quadcopters.co.uk


Inside the box


All contents come in a nice tidy box with all the parts labelled and in separate clear bags.
It is also small in size and well packed so shipping will be reasonable.
As you can see all the contents are clearly labelled making the build process much easier.
The build now begins
First off start by getting the bits you need which are the Frame arm plates, Nylon pillars , The motor and motor fixer.  Then fix the motors to the motor fixers using M3x6mm socket screws (use threadlock).
You should then end up with 4 like this below.
Once all 4 motors have been fixed to the motor fixing plates , then you can begin fastening them to the frame arm plates , again use threadlock on all metal to metal fixings.
It is best to start with one side first and also insert the Nylon pillars as shown in pic using M3 x8mm Nylon screws (take special care not to over tighten these ). If they feel tight going in , just back them off a quarter turn and carry on slowly. They will snap if over tightened .
Then put the other side frame arm together to look like this .
Repeat this process on all 4 arms , Note 2 are yellow for visibility.
You will then end up with them looking like this .
Now we prepare the Fuselage Upper Plate, you will need 8 frame arm fixers 
4x M3 nylon nuts , 4 x M3 x 12mm Nylon Pillars 
The picture shows the finished underside of the upper central plate, again use threadlock on the frame arm fixers, And carefully tighten nylon washers onto the pillars.
Pic below is the finished top of the upper center  plate.
Once the upper fuselage plate is finished we can begin to mount the frame arms 
See pic below , we use M2x6mm socket screws (threadlocked)
 
Repeat process on all 4 arms , and you will end up like this.
ESC and Motor connections
Now onto ESC and Motor connections.
Looking at the pic above the motor at 1 oclock is motor number 1 , 
11 o’clock is Motor 2,  7 o’clock is Motor 3 and finally 4 o’clock is number 4.
Start feeding the esc’s in as shown in the picture and feed the power lead 
to the underside and bring the signal wires through the centre hole as shown.
Motors 2 and 4 are black-black , red-red , yellow-yellow.
Motors 1 and 3 are black-red , yellow-yellow, red-black
Once all power connectors and signal wires have been fed through you can 
connect the JST connectors to the power wire (pre fitted with deans connector)

When all 4 wired up , it should look something like this.
Centre Plate

Now it is time to prepare the Bottom centre plate, you will need 8x Frame arm fixers 
and the M2 x 6mm socket screws (thread lock)
Now feed the battery velcro strap through the slots nearest the centre 
and the turn the frame upside down , grab a handful of M2 x6mm socket screws
and fix the bottom centre plate to the underside of the existing frame.


We now look like this.
Now we move onto fixing the Flight controller and the AHRS to the centre plate
Start off like this and pay close attention to which way everything is facing.
This build is for X style. But you only need to turn the flight controller and AHRS round for 
+ style.  First we attach the mounting plate onto the nylon pillars and then attach the supplied
double sided tape , this secures the flight controller.
Also have your signal wires from the Esc’s coming out like this as it will make the job neater.
Next we fasten the Flight controller onto the double sided tape , again make sure 
everything is facing the correct way.
What I did next was to update the firmware on the flight controller , the reason 
I choose to do this now , as nothing should be connected only the usb lead. 
This is all covered in the manual and on the xaircrafts wiki page
And then fixed the AHRS mounting plate onto the nylon pillars.
And now you stick 4 pieces of Shock absorbing double sided sponge pads to the 
underside of the AHRS unit and then stick onto the mounting plate.
Pay close attention to nose direction.  Arrow pointing forward to the nose. 
Also connect the Esc signal wires to their corresponding slots on the flight controller , They are labelled output 1-12 so Motor 1 goes to output 1 , and Motor 2 to output 2 and so on for the 4.
You can now also connect the Input wires to the FC board and then we can join them to our receiver.
Here we have 5 servo wires for , Throttle , Elevator , Rudder, Aileron, and Gear for Flight modes.
I have tidied the wires , and Bound my radio to the Ar6100e for this build. 
The radio set up is very easy. And is explained in more detail in the manual.
All there is to do now is check the motors are working , but do not run 
the motors fast or for a long time with no propellers on as this could 
cause damage. Once I was happy with everything I put the props on .
Motors 1 and 3 should turn CCW and Motors 2 and 4 are CW.
Put the props on and tighten prop adapters.
I have added a security dummy cam dome on this build which I think 
gives it a nice look.
After this was assembled I did a quick hover indoors and it flew very well
I will do more testing and hopefully get some flying time with this soon.

This is only a guide and I cannot be held responsible if I have made any errors in writing this. The full instructions do come with all kits and the final build and quality is down to your experience.


Thanks for reading.

Xaircraft Gps and Compass Released

Xaircraft have released the Gps and Compass module and quadcopters uk have given a set to Joshbb who is one of the original testers for Xaircraft X650 and a very active and valuable member of RCGroups and also Quadcopters Uk forums , We are hoping for some good feedback from Joshbb and we will keep you all posted with his findings.
Buy the Gps and compass module from Quadcopters XAircraft Gps Here and XAircraft Compass Here

XAircraft Uk and Europe Distributor

http://www.quadcopters.co.uk/ are already the leading dealers and distributors of XAircraft and Quadcopter products in the UK and so as a result we are launching a dedicated European Site for our EU friends. This will be a live shop with upto the minute live currency conversion so you will pay in Euros based on the actual rate , Other sites make there own rates of exchange up.
The new site will be dedicated purely on XAircraft products and bringing all the latest news and developments from the Xaircraft team.
The web url for the new site is http://www.xaircraft.eu/ More info to follow.
So if your looking to buy a XAircraft Quad Copter for recreational or aerial photo work please visit Buy Xaircraft Here
Reasons to Choose Quadcopters Uk and Xaircraft.eu are we are purely dedicated to quadcopters and we have sponsored pilots and technical support so we can assure all the products we sell are tested .
Largest stocks of Xaircraft Quadcopters and Parts and accessories. Support forums and also email and phone support, we believe this is important to helping customers get the best from there quad.
Here below is a video from our very own EU tester Norf demonstrating the XAircraft X450 in action.